A

Adjali, H., Davies, M., Rees, R.W. and Littler, J. (1999) The testing of a numerical model's ability to simulate heat transfer from slab-on-grade floors and the implication for low-energy design. In: Proceedings of the National Passive Solar Conference 1999; 12 -16 Jun 1999, Portland, U.S.A.. ISBN 9780895531711

B

Blackman, B.R.K., Hadavinia, H., Kinloch, A. J. and Paraschi, M. (1999) Determining the adhesive fracture energy of bonded joints. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 425-430. 1999

C

Curley, AJ, Williams, KJ, Le, T and Patel, H (1999) The cyclic fatigue behaviour of ball grid arrays. Microelectronics International, 16(3), pp. 43-45. ISSN (online) 1356-5362

D

Davies, Michael, Zoras, Stamatis and Adjali, Hicham (1999) A potentially fast, flexible, and accurate earth-contact heat-transfer simulation method. In: Building Simulation; 13 - 15 Sept 1999, Kyoto, Japan.

F

Fern, A., Mason-Jones, A., Pham, D. T. and Wang, J. (1999) Design and Performance Predictability of Valve Stem Seals Using FEA. (Technical Report) Warrendale, PA., U.S. : SAE International. (SAE Technical Paper 1999-01-0883)

G

Giaccone, PR, Jones, GA, Minelly, S and Curley, AJ (1999) Motion-compensated multichannel noise reduction of colour film sequences. Journal of Electronic Imaging, 8(3), pp. 246-254. ISSN (online) 1017-9909

Grant, RJ and Smart, J (1999) Crack growth in pin-loaded tubes: part 1: numerical analysis. The Journal of Strain Analysis for Engineering Design, 34(4), pp. 253-269. ISSN (print) 0309-3247

Grant, RJ and Smart, J (1999) Crack growth in pin-loaded tubes: part 2: comparison of experimental data with numerical results. The Journal of Strain Analysis for Engineering Design, 34(4), pp. 271-284. ISSN (print) 0309-3247

H

Hadavinia, H., Blackman, B.R., Kinloch, A. J., Ring-Groth, M. and Williams, J.G. (1999) The peel testing of adhesively-bonded joints. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 243-250. 1999

Harjoprayitno, W.W., Hadavinia, H. and Kinloch, A. J. (1999) Epoxy-moulded products: studying and increasing the interfacial adhesion. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 341-346. 1999

L

Liu, F. and Wen, J.X. (1999) Development and validation of an advanced turbulence model for buoyancy driven flows in enclosures. International Journal of Heat and Mass Transfer, 42(21), pp. 3967-3981. ISSN (print) 0017-9310

M

Monekosso, Ndedi (1999) On-board reasoning for an autonomous spacecraft. (PhD thesis), University of Surrey, .

S

Sabir, H. M. and Eames, I. W. (1999) Performance of film absorbers under the effect of a contaminant non-absorbable gas. Applied Energy, 63(4), pp. 255-267. ISSN (print) 0306-2619

Sabir, H.M., Eames, I.W. and Suen, K.O. (1999) The effect of non-condensable gases on the performance of film absorbers in vapour absorption systems. Applied Thermal Engineering, 19(5), pp. 531-541. ISSN (print) 1359-4311

T

Talal, Sina (1999) Effect of long-term compression on rigid polymer foams. (PhD thesis), Kingston University, .

Z

Zhang, T., Evans, J.R.G. and Bevis, M. (1999) Relaxation patterns in powder injection mouldings made with repeated flow reversals. Journal of the European Ceramic Society, 19(4), pp. 411-417. ISSN (print) 0955-2219

Zweiri, Yahya, Whidborne, J. F. and Seneviratne, L. D. (1999) Dynamic simulation of a single-cylinder diesel engine including dynamometer modelling and friction. Proceedings of the Institution of Mechanical Engineers - Part D: Journal of Automobile Engineering, 213(4), pp. 391-402. ISSN (print) 0954-4070